What appliances need a fused spur?

Fused spurs are commonly used as an alternative to a conventional socket, for the installation of powerful electrical appliances that can be installed without a plug, such as ovens, washing machines, electric heaters, dishwashers, fridges, and so on.

.

In this regard, do you need a fused spur for a fridge?

1 - fused spurs are not required, most appliances just plug in. Isolation is achieved by removing the plug from the socket. Cookers and some ovens will require their own circuit.

One may also ask, do you need a fused spur for an electric fire? An electric fireplace is one of the appliances whose power rating does not permit you to plug into an ordinary wall socket. That is why a fused spur is the recommended way to go about this wiring process. There's likelihood you're going to be tempted to just put a plug socket next to the fused spur on the wall.

Similarly, it is asked, what is a fused spur used for?

A Fused Spur Switch is commonly used for powerful electrical appliances, such as washing machines and dish washers that need to be installed without a plug; they are also used for electrical items that need to be installed on a separate cable from the ring main, for safety and maintenance purposes.

Can you run a spur off a spur?

And you need to be certain that any point that you intend to take a spur from is actually part of a ring and not a spur already. Spurring off spurs is a no - particularly in a kitchen where the loading on sockets will be higher than anywhere else in a house.

Related Question Answers

Can I fit a fused spur?

As long as the job isn't within a 'special location' such as a bathroom or outdoors, you're also allowed to install additional new light fittings, switches, sockets and even add a single fused spur to an existing circuit (a 'spur' is a new cable and socket run as a branch from an existing socket on the ring main).

Does a dishwasher need a fused spur?

Fused spurs are commonly used as an alternative to a conventional socket, for the installation of powerful electrical appliances that can be installed without a plug, such as ovens, washing machines, electric heaters, dishwashers, fridges, and so on.

Can you put a double socket on a fused spur?

you can have maximum one double socket as a normal spur but if you are going from socket to FCU fused at 13 amp from there you can add as many sockets as you wish as all the sockets and cable will be protected by the fuse so no chance of overloading the cable the fuse will blow first.

Can you spur off a socket?

The easiest way of connecting into a ring circuit is to run a spur cable from the terminals of an existing socket – but you can't connect it to any socket. An alternative to running a spur from an existing socket is to run it from a 3-terminal, 30-amp junction box wired into the main circuit cable.

Do kitchen appliances require isolation?

Local Isolation for Kitchen Appliances. Local isolation is generally required for all items of electrical equipment for maintenance, service & repair.

What is a non fused spur?

Fused spurs are connected to the ring circuit through a fused connection unit,the fuse of which must not exceed 13A,or the rating of the cable taken from the fused spur. A non-fused spur can only feed one single or one twin socket outlet,or one permanently connected item of equipment.

How long is an electrical spur?

The maximum length allowed for an unfused spur is 3m. The general rule of thumb, is that you can have an unfused spur at each socket, and one at the CU.

Can I run wall lights from a socket?

Re: Adding wall lights - run from an existing socket? lights need to be a lower fuse rating so you must wire this switched form a switched fused spur. then take the fuse out of it and change it for a 2-3amp one. use 2.5mm T&E cable from the socket to the switched fuse spur and then 1.5mm to the lights.

How many times can you spur off a socket?

A spur can be connected to an existing socket, on either a ring main or a radial circuit, providing that socket does not already have a spur. That is only one spur per socket is allowed and the number of spurs must not exceed the number of sockets.

Can you change a fused switch to a socket?

There is no problem removing 13amp fused spurs and replacing with socket outlets. You just need to ensure that those circuits (fuses/mcb's) are backed up by a 30ma RCD as they will now be used to supply mobile equipment rather than fixed.

Can I use a fused spur as a light switch?

You will probably use 2.5 mm or above cable. You can either fit a switched fused spur unit, which will act as the light switch. Alternatively, fit an unswitched fused spur unit, THEN an oridinary light switch. The fused spur unit will need a 3 or 5 amp fuse.

Can you put a fused spur on a ring main?

A fused spur can be added as part of the ring or it can be a spur of a socket that is part of the main ring that is not spurred from already.

What amp fuse do I need for an electric fire?

for appliances up to 700 watts, use a 3 amp fuse. for appliances between 700 and 1,000 watts, use a 5 amp fuse. for appliances more than 1,000 watts, use a 13 amp fuse.

What fuse does a tumble dryer need?

Given that the tumble dryer will have a 13 amp fuse in the plug that's plugged into this socket, connected via this approx 3 feet of mains cable to another plug with a 13 amp fuse, and plugged into a ring main power socket.

Can you hardwire an electric fireplace?

Most built-in electric fireplaces have a cord that you can plug into a standard electrical outlet that you can install inside the opening (if allowed by your local code). Another option is to remove the cord and hardwire the fireplace as most units are hardwire ready.

Can I use 1.5 mm cable for sockets?

Using 1.5mm in a ringmain is OK as the purpose is to reduce the overall thickness of the cable needed to provide the same voltage. As you are putting a spur it 1.5mm is fine as long as you don't use more than 16 amps.

Can you use a junction box to extend wiring?

If you do need to extend the wires, yes, a junction box would be needed. It must remain accessible. You've pretty well identified your two choices; if you don't want to re-run longer cables, you'll need to splice in some additional cable.

Which is feed and load on fused spur?

The feed is the cable from your fuse board, supplying the power to the isolator switch. The load is the cable supplying the appliance once you have switched the isolator into the on position.